Oki C810 Maintenance Manual Download Page 133

Page: 133 / 253

44015503TH Rev. 1

132 /

Oki Data CONFIDENTIAL

5. MAINTENANCE MENUS

5.3.2.4 Motor and clutch test

The motor and clutch test is used for testing motors and clutches.

1. Enter the self-diagnostic mode (level 1) and, until MOTOR & CLUTCH TEST

appears on the upper display, press the MENU up-arrow ( ) or MENU down-arrow

( ) button (the MENU up-arrow ( ) button displays the next test option and the

MENU down-arrow ( ) button displays the preceding test option). Then press the

ENTER button.

2. Press the MENU up-arrow ( ) or MENU down-arrow ( ) button until an option

shown in table 5-4 for the unit to test appears on the lower display (the MENU up-

arrow ( ) button displays the next option and the MENU down-arrow ( ) button

displays the preceding option).

MOTOR & CLUTCH TEST

ID MOTOR

3. Press the ENTER button. The motor and clutch test starts, the unit’s the name and

current status starting to blink, and the unit being driven for ten seconds (refer to

figure 5-2).

Note! The state in step 2 is restored after the unit is driven so. The unit is driven

again by pressing an appropriate button.

• By usual printing driving, the clutch solenoid repeatedly is turned on and

off (its motor is driven together with the solenoid when the solenoid cannot

be driven solely for its mechanical structure). * Image drum up-and-down

movement continues until the CANCEL button is pressed.

• The clutch solenoid is kept driven by holding down the ENTER button (two

seconds) for a motor to be accepted.

4. Press the CANCEL button. The state in step 2 is restored.

5. Repeat steps 2 through 4 when necessary.

6. Press the BACK button to end the test (the state in step 1 is restored).

Tray-1 hopping motor
(registration motor
and front motor)

Hopping solenoid

Tray-2 hopping clutch

Tray-3 hopping clutch

Image drum motor

Fuser motor

Fuser-end cooling fan

Fuser fan

Duplex fan

Color registration shutter

Duplex
solenoid

Duplex
clutch

Duplex
motor

Tray-2 motor

Tray-2 feed clutch

Tray-3 motor

Tray-3 feed clutch

Belt motor

Lv (low voltage) fan

Image drum up-down motor

Figure 5-2

Summary of Contents for C810






























































































































































































































































Search results

Summary of Contents for C810

Reviews:

Oki C810, Maintenance Manual, Page: 133 / 253

Search results

Summary of Contents for C810

Reviews: