manualshive.com logo in svg

Oki C810, Maintenance Manual, Page: 178 / 253

Share
Download
Oki C810 Maintenance Manual Download Page 178

44015503TH  Rev. 1 

177 /

Oki  Data  CONFIDENTIAL

7.  TROUBLESHOOTING PROCEDURE

Display

Cause

Error details

Remedial measure

Contact the Service 
center. 
181: error
182: error 
183: error

Option unit I/F 
error

(181=Duplex 
Unit, 182=2nd 
Tray, 183=3rd 
Tray)

Does this error recur?

 
Does this error recur?

yes

 

yes

Turn on the power again.

Check for sure connection 
of the connectors.

Replace the option unit.

Contact the Service 
center. 
190: Error

System 
memory 
overflow

Does this error recur?

yes

Turn on the power again.

Increase the add-on RAM 
DIMM. 

Contact the Service 
center. 
200: error 
   ~
202: error

PU Firmware 
Download 
Error

Error has occurred during 
rewriting of the PU firmware.

After turning on the 
power again, perform 
downloading again. 
(This error does not 
occur during the normal 
operation because this 
processing is not carried 
out.)

Reboot the printer.
209: Download error

Custom Media

Type table 
downloading 
has failed.

Custom Media Type table 
downloading has failed.

After turning on the 
power again, perform 
downloading again. 
(This error does not 
occur during the normal 
operation because this 
processing is not carried 
out.)

Reboot the printer.
203: error
204: error
207: error
208: error 
213: error
214: error
FOC: error 
FOD: error
FFF: error

CU program 
error

(Mentioned 
any error 
numbered from 
203 to 214 
does not occur 
under normal 
operation.)

Illegal processing is executed 
by the CU program.

After turning off the 
power, check the normal 
connection between CU 
board and PU board. 
Then, turn on the power 
again.

Contact the Service 
center.
230: error

RFID Reader 
not lnstaled

RFID read device error 
 

Does this error recur?

yes 

 

yes

Check the normal 
connection of RFID R/W 
board.

Replace the RFID R/W 
board. Replace the P6X 
board.

Display

Cause

Error details

Remedial measure

Contact the Service 
center.
231: error

RFID reader 
I/F error

Interface error with the RFID 
reader is detected.

01: Communication error 

between the RFID reader 
and the engine circuit 
boards.

02: Error in the wireless circuit 

of the RF ID reader

03: Communication error 

between the RFID reader 
and the tag chip.

04: Error is detected in the 

RFID tag chip. (In more 
than 4 chips)

01: Same as the error no. 

230

02: Replace the RFID 

R/W board.

03: Check for normal 

connection of the 
antenna cable.

04: Check if quantity 

of the RFID Tag is 
correct or not.

Reboot the printer. 
250: Error

The erasing 
error of 
encrypted 
file has been 
detected. 

Has the User known that HDD 
ERASE is performed? 

 yes 

 

  

Inform the User that it is 
necessary to perform Disk 
ERASE and revert the 
HDD as the purchasing 
status in order to delete 
the encrypted file. (ADMIN 
MENU HDD ERASE) 

Contact the Service 
center. 
251: Error 

Secure Disk 
Erasing Error

Error has been detected in the 
Disk ERASE. 

Does the error display recur? 

 

yes

Electrical power OFF/ON 

Replace HDD 

Contact the Service 
center. 
252: Error 
253: Error 

Disk Security 
Mode Error

Install hard disk that has 
been connected while 
introducing the security kit. 

Contact the Service 
center. 
254: Error 

Disk Security 
Mode Error

Does the error display recur? 

yes

Turn the power OFF/ON.

Regenerate the encrypting 
mode. If it still does not 
improve the situation, 
change the CU board and 
encrypted hard disk.   

Contact the Service 
center. 
255: Error 

Disk Security 
Mode Error

Only change the 
encrypted board. 

Contact the Service 
center. 
256: Error 

Disk Security 
Mode Error

Install genuine hard disk. 

Summary of Contents for C810






























































































































































































































































Reviews:

No comments