Oki C810 Maintenance Manual Download Page 142

Page: 142 / 253

44015503TH Rev. 1

141 /

Oki Data CONFIDENTIAL

5. MAINTENANCE MENUS

5.3.2.8 Consumable counter display

The consumable counter display is used for viewing the usage of consumables.

1. Enter the self-diagnostic mode and, until CONSUMABLE STATUS appears, press

the MENU up-arrow ( ) or MENU down-arrow ( ) button (the MENU up-arrow ( )

button displays the next test option and the MENU down-arrow ( ) button displays

the preceding test option). Then press the ENTER button.

2. Pressing the MENU up-arrow ( ) or MENU down-arrow ( ) button displays the

usage of each consumable (pressing the ONLINE or CANCEL button is disabled).

3. Press the BACK button to end the option (the state in step 1 is restored).

Upper display

Lower display

Display

format

Display

unit

Detail

K-ID UNIT

********IMAGES

Decimal Images

Each displays the number of

turns performed by an image

drum unit in three-pages-per-job

printing to date after the first-time

installation of it, converted on an

A4 page basis.

y-ID UNIT

********IMAGES

Decimal Images

M-ID UNIT

********IMAGES

Decimal Images

C-ID UNIT

********IMAGES

Decimal Images

FUSER UNIT

********PRINTS

Decimal

Prints

Displays the number of prints

made to date after the first-time

installation of a fuser unit.

TR BELT UNIT

********IMAGES

Decimal Images

Displays the number of prints

made to date after the first-time

installation of a belt unit.

K-TONER

(FULL)

********%

Decimal

Each displays the usage of toner

of a color.

y-TONER

(FULL)

********%

Decimal

M-TONER

(FULL)

********%

Decimal

C-TONER

(FULL)

********%

Decimal

Upper display

Lower display

Display

format

Display

unit

Detail

M-WASTE

TNR CNT

********TIMES

Decimal

Times

Each displays the amount of

waste toner. * 32 times or more

indicates the printer is full of

waste toner.

C-WASTE

TNR CNT

********TIMES

Decimal

Times

K-STC MODE

CNT

********TIMES

Decimal

Times

Each displays the print dot count

of toner of a color (life counter

value after the printer goes into

operation).

y-STC MODE

CNT

********TIMES

Decimal

Times

M-STC MODE

CNT

********TIMES

Decimal

Times

C-STC MODE

CNT

********TIMES

Decimal

Times

K OvER RIDE

CNT

********TIMES

Decimal

Times

Each displays the extension

life counter value of a toner

cartridge.

y OvER RIDE

CNT

********TIMES

Decimal

Times

M OvER RIDE

CNT

********TIMES

Decimal

Times

C OvER RIDE

CNT

********TIMES

Decimal

Times

Summary of Contents for C810






























































































































































































































































Search results

Summary of Contents for C810

Reviews:

Oki C810, Maintenance Manual, Page: 142 / 253

Search results

Summary of Contents for C810

Reviews: