Oki C810 Maintenance Manual Download Page 38

Page: 38 / 253

44015503TH Rev. 1

37 /

Oki Data CONFIDENTIAL

3. INSTALLATION

Installing the image drum cartridges

(1) Take out the image drum cartridge (four cartridges) gently.

Note! • The image drum (green cylinder part) is very sensitive to scratches,

therefore, special care should be taken on handling.

• Do not expose the image drum cartridges to direct sunlight or strong light

(approx. 1500 lux or above). Even under room light, do not leave them

exposed for five minutes or longer.

(2) Put the image drum cartridge on newspaper or something, remove the tape holding

the protective sheet, and pull the sheet out in the direction of the arrow.

Image drum cartridge

(3) Remove the toner cover.

(4) Similarly, remove the protective sheets and toner covers fro the other three image

drums.

Protective sheet

Tape

Protective sheet

Tab

Toner cover

Summary of Contents for C810






























































































































































































































































Search results

Summary of Contents for C810

Reviews:

Oki C810, Maintenance Manual, Page: 38 / 253

Search results

Summary of Contents for C810

Reviews: