manualshive.com logo in svg

Oki C810, Maintenance Manual, Page: 13 / 253

Share
Download
Oki C810 Maintenance Manual Download Page 13

44015503TH  Rev. 1 

12 /

Oki  Data  CONFIDENTIAL

1.  CONFIgURATION

Classification

Item

Specification(s)

Service life

Transfer belt life

80,000 pages (A4 LEF, 3 pages/job),

counter automatic reset 

Fuser unit life

100,000 pages (A4), counter automatic reset 

Operation 

noise 

Operating

54 dBA (ISO 7779 Front)

(without any optional unit)

Standby

37 dB (ISO 7779 Front) 

Power save mode

Background level 

Paper 

handling 

Tray capacity (1st tray) 

Legal/universal cassette: 300 sheets (70 kg) 

Tray capacity (2nd/3rd 

tray) 

Legal/universal cassette (option):

530 sheets (70 kg)

Tray capacity (manual/

auto)

Standard multipurpose tray:

100 sheets (70 kg) or 10 envelopes 

Paper ejection 

250 sheets (70 kg) to the face down stacker, 

100 sheets (70 kg) to the face-up stacker 

Duplex

Standard 

Paper size 

A3, A4, A5, A6*, B4, Letter, Legal (13/13.5/14 

inches), Executive, postcard**, double-postcard**, 

Custom***, envelope (Choukei 3, Youkei 0, Youkei 

4, Kakugata 2, Kakugata 3.)

*:  A6 size paper cannot be printed from trays 2 

and 3.

**:  Postcards and double-postcards can be 

printed only from the MPT.

***: As for Custom, the available size differs 

depending on trays. 

Minimum 

paper size 

Tray 1

A6

Tray 2, Tray 3 (options)

A5

MPT

Postcard 

Media 

weight 

Tray 1

64 g/m

2

 to 120 g/m

2

Tray 2, Tray 3 (options)

64 g/m

2

 to 175 g/m

2

MPT

64 g/m

2

 to 200 g/m

2

Classification

Item

Specification(s)

Operator 

panel 

LCD

graphic panel with 128 × 64 dots,

no display of paper size

LED (color)

2 LEDs (green × 1, dark amber × 1) 

Switch

8 switches 

Status 

switch/

sensor 

Paper out

Provided

Paper low

Not provided

Toner low

Provided (Y, M, C, K)

Cover open

Provided

Fuser temperature

Provided

Paper size

Provided (manual setting) 

Stacker full

Not provided 

Communica-

tion interface 

Standard (on-board) 

• High-speed USB 

• Ethernet 

• Parallel interface

Option

N/A

Input/output switch 

Automatic 

Emulation 

Standard 

PCL (PCL5c, HP-gL) / PCL XL 2.1

PostScript 3 (Clone)

Emulation switch 

Automatic

Font

Bit-map typeface

Provided

Scalable font

Provided

Rasterizer

Provided

Barcode

Provided

OCR

Provided

Japanese PCL font

Provided

Japanese PS font

Provided

Summary of Contents for C810






























































































































































































































































Reviews:

No comments