Oki C810 Maintenance Manual Download Page 51

Page: 51 / 253

44015503TH Rev. 1

50 /

Oki Data CONFIDENTIAL

3. INSTALLATION

Note! • Proper operation by use of an unspecified product cannot be guaranteed.

Be sure to use Oki product.

• Additional memory of 256 MB or more is recommended for long-sheet

printing.

• One memory slot is provided.

(3) Installation of an additional memory

A memory expansion board increases the memory capacity of the printer. A memory

expansion board should be added to the printer when an error message [Memory Overflow]

appears due to insufficient memory for complex data on the printer, or the error message

[Collating Error] appears in making collated sets of copies.

Additional memory

Model name

Memory capacity (total)

None (standard)

256 MB (256 MB)

MEM256E

+256 MB (512 MB)

MEM512C

+512 MB (768 MB)

1. turn off the printer and disconnect the power cord.

Turn off the printer by following the steps described under “Turning off the power” in

section 3.5.2.

Note! • The printer or additional memory may fail if the power is switched off without

taking shutdown steps. Be sure to follow the shutdown procedure.

• Installation of an additional memory with power on may cause a failure of

the printer.

OPEN button

Multi-purpose tray

Handle

2. open the top cover and the front cover.

Open the multi-purpose tray.

Push the OPEN button to open the top

cover.

Front cover

Push up the (blue) lever at the center

of the front cover and pull the cover to

open.

Summary of Contents for C810






























































































































































































































































Search results

Summary of Contents for C810

Reviews:

Oki C810, Maintenance Manual, Page: 51 / 253

Search results

Summary of Contents for C810

Reviews: