Oki C810 Maintenance Manual Download Page 143

Page: 143 / 253

44015503TH Rev. 1

142 /

Oki Data CONFIDENTIAL

5. MAINTENANCE MENUS

5.3.2.9 Print counter display

The print counter display is used for viewing print counter values.

1. Enter the self-diagnostic mode and, until PRINTER STATUS appears, press the

MENU up-arrow ( ) or MENU down-arrow ( ) button (the MENU up-arrow ( )

button displays the next test option and the MENU down-arrow ( ) button displays

the preceding test option). Then press the ENTER button.

2. Pressing the MENU up-arrow ( ) or MENU down-arrow ( ) button displays each

count printed (pressing the ONLINE or CANCEL button is disabled).

3. Press the BACK button to end the option (the state in step 1 is restored).

Upper display

Lower display

Display

format

Display

unit

Detail

K-

IMPRESSIONS

********IMAGES

Decimal Images

Each displays the number of

each color’s images printed.

IMPRESSIONS

********IMAGES

Decimal Images

M-

IMPRESSIONS

********IMAGES

Decimal Images

C-

IMPRESSIONS

********IMAGES

Decimal Images

TOTAL SHEET

CNT

********COUNTS

Decimal

Prints

Displays the total number of

images printed.

5.3.2.10 Factory-shipping mode switching

The Factory-Shipping mode switching is used for switching from the Factory to Shipping

mode.

1. Enter the self-diagnostic mode and, until the following message appears, press the

MENU up-arrow ( ) or MENU down-arrow ( ) button.

FACTORY MODE SET

2. Press the MENU up-arrow ( ) or MENU down-arrow ( ) button. The following

message appears. Press the MENU up-arrow ( ) or MENU down-arrow ( ) button

until the option to set (refer to the table shown below) appears.

FACTORY MODE

SHIPPING MODE *

3. A setting for the option can be selected by pressing the ENTER button with the

option on the display.

4. Hold down the ENTER button (for three seconds) with the setting on the display.

The setting is stored in the EEPROM. The state in step 2 is restored.

5. Repeat steps 2 through 4 when necessary.

6. Press the BACK button to end the option (the state in step 1 is restored).

Option

Settings

Function

FACTORy

MODE

FACTORy MODE

Establishes the Factory mode (a fuse-cut disabling

mode).

SHIPPING MODE

Deselects the Factory mode to enable the fuse-cut

function.

FUSE INTACT

Note:

Six asterisks

(******)

identifies

INTACT or

BLOWN.

BELT UNIT ******

Displays the fuse status of the transfer belt unit.

FUSE UNIT ******

Displays the fuse status of the fuser.

K-ID UNIT ******

Displays the fuse status of the black image drum unit.

y-ID UNIT ******

Displays the fuse status of the yellow image drum unit.

M-ID UNIT ******

Displays the fuse status of the magenta image drum

unit.

C-ID UNIT ******

Displays the fuse status of the cyan image drum unit.

Summary of Contents for C810






























































































































































































































































Search results

Summary of Contents for C810

Reviews:

Oki C810, Maintenance Manual, Page: 143 / 253

Search results

Summary of Contents for C810

Reviews: