Oki C810 Maintenance Manual Download Page 39

Page: 39 / 253

44015503TH Rev. 1

38 /

Oki Data CONFIDENTIAL

3. INSTALLATION

(5) Install the toner cartridges to the image drum cartridges.

Note! The toner cartridges supplied with the product are capable of printing

approximately 2,300 sheets (ISO/IEC 19798).

a) Take the toner cartridge out of its package and shake the toner cartridge

several times vertically and horizontally.

b) Hold the toner cartridge in a horizontal position and slowly remove the tape.

c) Make sure that the color of the toner cartridge’s label matches the color of the

image drum cartridge’s label.

d) Engage the hole of the toner cartridge with the post of the image drum

cartridge with the side with the tape removed facing down.

e) Push the toner cartridge in so that the right groove in the cartridge is engaged

with the protrusion of the cartridge guide.

Turn the lever on the toner cartridge in the direction of the arrow until it stops.

Note! • Do not force the toner cartridges into place. If the cartridges do not fit, check

to see if the color of the lever on each of the toner cartridges corresponds to

the color of the label on each of the image drum cartridges. If the colors of

these labels do not correspond, the toner cartridges cannot be installed.

• The print quality may deteriorate if the toner cartridges are not installed

properly.

(6) Install the image drum cartridges with the toner cartridges installed to the printer.

(7) Close the top cover.

Note! If the message [REPLACE TONER] on the operator panel remains displayed

even after a long period of waiting, check to see if the lever on the toner

cartridge is moved fully in the direction of the arrow.

Label

Tape

Toner cartridge

Image drum cartridge

Post

Toner cartridge

Cartridge guide

Groove

Hole

Summary of Contents for C810






























































































































































































































































Search results

Summary of Contents for C810

Reviews:

Oki C810, Maintenance Manual, Page: 39 / 253

Search results

Summary of Contents for C810

Reviews: