Oki C810 Maintenance Manual Download Page 156

Page: 156 / 253

44015503TH Rev. 1

155 /

Oki Data CONFIDENTIAL

6. CLEANING

6.3 Pick-up roller cleaning

The pick-up rollers must be cleaned when a vertical line occurs on printed output.

Note! Use a soft cloth to clean the pick-up rollers so as not to damage their surfaces.

Paper feed roller and pad cleaning

When frequent ‘SLIDE OUT TRAy-PAPER JAM [tray name]’ messages occur, clean the

paper feed rollers and pad of the tray identified by the tray name in the message.

(1) Pull out the paper cassette of the tray being displayed.

(2) Wipe the paper feed rollers (large and small) with a cloth tightly wrung out with

water.

(3) Wipe the pad of the paper cassette with a cloth tightly wrung out with water.

Note! When frequent ‘OPEN COvER-PAPER JAM-FRONT COvER’ messages

occur, clean the paper feed roller of the multi-purpose tray in the same manner

as described above.

Paper feed roller (large)

Paper feed roller (small)

Pad

Summary of Contents for C810






























































































































































































































































Search results

Summary of Contents for C810

Reviews:

Oki C810, Maintenance Manual, Page: 156 / 253

Search results

Summary of Contents for C810

Reviews: