Home
/
Oki
/
C810
/
Maintenance Manual

Oki C810, Maintenance Manual, Page: 135 / 253

Share

Page: 135 / 253

Oki C810 Maintenance Manual Download Page 135

44015503TH Rev. 1

134 /

Oki Data CONFIDENTIAL

5. MAINTENANCE MENUS

5.3.2.5 test printing

The test printing is used for printing test patterns stored in the PU. Other patterns are stored

in the controller.

1. Enter the self-diagnostic mode (level 1) and, until TEST PRINT appears on the

upper display, press the MENU up-arrow ( ) or MENU down-arrow ( ) button (the

MENU up-arrow ( ) button displays the next test option and the MENU down-arrow

( ) button displays the preceding test option). Then press the ENTER button.

2. A setting option used only in test printing appears on the lower display. Press the

MENU up-arrow ( ) or MENU down-arrow ( ) button until the option to select

appears (the MENU up-arrow ( ) button displays the next option and the MENU

down-arrow ( ) button displays the preceding option). Then press the ENTER

button. (Go to step 5 when, left set to its default, the option does not need to be

set).

3. The setting option and its setting appears on the upper and lower displays,

respectively. Pressing the MENU up-arrow ( ) button displays the next setting

and pressing the MENU down-arrow ( ) button displays the preceding setting (the

setting last displayed takes effect. By pressing the BACK button, the setting is

accepted, step 2 being restored. Repeat step 3 when necessary.

TEST PATTERN

1

Option

Settings

Function

PRINT EXECUTE

–

Starts printing with the press of the ENTER
button, and ends printing with the press of the
CANCEL button.

TEST PATTERN

0

0: Prints a blank page.
1 to 7: - See the next section (pattern printing) -
8 to 15: Print a blank page.

TEST CASSETTE

TRAy1

Selects a paper source
Not displayed when the tray 2 is not installed.
Not displayed when the tray 3 is not installed.

TRAy2

TRAy3

MFP

PAGE

0000

Sets the number of test copies printed

COLOR

ON

Selects color or monochrome printing.
* Each color setting is provided by setting ON.

OFF

DUPLEX

2 PAGES STACK

Prints duplex two pages stack layout printing.

OFF

Disables duplex printing.

1PAGES STACK

Prints duplex one page stack layout printing.

MONO SPEED

LOW

Selects a monochrome-print speed:
LOW: 30 ppm
HIGH: 32 ppm

HIGH

• A default is in a shaded area (

). Set settings are enabled only in this test mode (not

written into EEPROM).

Note! PAGE setting:

The input position is shifted with the MENU up-arrow ( ) or
MENU down-arrow ( ) button.  This setting is incremented
by  pressing  the  ONLINE  button,  and  decremented  by
pressing  the  CANCEL  button.    Note  the  setting  0000
endlessly prints pages.

COLOR setting: ON displays, with the press of the ENTER button, the

information shown below.

Print setting for each color: The input position is shifted with the MENU up-

arrow ( ) or MENU down-arrow ( ) button. This setting is
switched between ON and OFF by the press of the ONLINE
or CANCEL button. The display for the setting restored to
the previous one with the press of the BACK button.

COLOR

Y:ON M:ON

ON

C:ON K:ON

«
...
133
134
135
136
137
...
»

Summary of Contents for C810






























































































































































































































































Reviews:

No comments