Home
/
Oki
/
C810
/
Maintenance Manual

Oki C810, Maintenance Manual, Page: 160 / 253

Share

Page: 160 / 253

Oki C810 Maintenance Manual Download Page 160

44015503TH Rev. 1

159 /

Oki Data CONFIDENTIAL

7. TROUBLESHOOTING PROCEDURE

Panel display

ON

LINE
lamp

Inspec-

tion

lamp

Details

Erasing Disk
nnn%

Off

Off

Indicates that it is in elimination process for hard
disk.
The erasure process for hard disk can be actuated
from [Storage Setup] of Boot Menu - [Erase HDD].

Checking Sectors
nnn%

Off

Off

Indicates that the sector of HDD is being checked.
The sector check process can be actuated from
[Storage Setup] of Boot Menu - [Check All Sectors]

Program Update Mode

Off

Off

Indicates that the printer has entered in the
dedicated mode for upgrading the NIC program
(controller firmware) version.
For actuating this mode is to turn on the Electric
power by pressing the Online button.

Wait a Moment
Program Data Received

Off

Blink Indicates that reception of the NIC program data

for upgrading is in progress.

Wait a Moment
Program Data Received
OK

Off

Off

Indicates that reception of the NIC program data for
upgrading is complete.

Check Data
Program Data Receive
Error
%DLCODE%

Off

On

Indicates that an error has occurred during
reception of the NIC program data for upgrading.
%DLCODE%

1 : Size error
2 : Checksum error
3 : Printer model number error
4 : Module I/F version error
5 : FAT version error

Wait a Moment
Program Data Writing

Off

Blink Indicates that writing of the NIC program data for

upgrading is in progress.

Power Off/On
Program Data Writing
OK

Off

Off

Indicates that writing of the NIC program data for
upgrading is in complete.

Panel display

ON

LINE
lamp

Inspec-

tion

lamp

Details

Check Data
Program Data Write
Error
%DLCODE%

Off

On

Indicates that an error has occurred during writing
of the NIC program data for upgrading.
%DLCODE%

1 : Memory allocation error
2 : Download file error
3 : Device free space acquisition error
4 : Device insufficient free space error
5 : File write error
6 : CU-F/W mismatch error

PU Flash Error

Off

Off

Indicates that the PU firmware has started up in
the Loader mode.
This error can occur in the user environment. If
this error occurs, maintenance by a maintenance
engineer is required. (Same as S/C)

Communication Error

Off

Off

Indicates that communication with the PU firmware
has failed. This error can occur in the user
environment. If this error occurs, maintenance by
a maintenance engineer is required. (Same as S/C)

Status Mode

Off

Off

Indicates that the printer has started in the ON
LINE mode always. When a printer starts up in
this mode, it processes the data (job) from outside
(host) even when an error occurs if a printer has
entered the ON LINE mode once.
Error and warning are displayed on the panel.
A printer can enter in this mode if the power of a
printer is turned on while pressing the button of
<Enter> + <Back> + <Down> all simultaneously.
Because this pattern of pressing the multiple
button at the same time at power-on is not
disclosed to user, this status will not occur in the
user environment.

«
...
158
159
160
161
162
...
»

Summary of Contents for C810






























































































































































































































































Reviews:

No comments