Oki C810 Maintenance Manual Download Page 124

Page: 124 / 253

44015503TH Rev. 1

123 /

Oki Data CONFIDENTIAL

5. MAINTENANCE MENUS

Option

Adjustment

Section in

Maintenance

Utility

operation

manual

Operation from

operator panel

(section in this

maintenance

manual)

12 Destina-

tion/ PnP
information
setup

Sets or checks the (CU) destination, device
identification and USB identification.

2.4.1.2.9

5.4.3

13 Consuma-

ble counter
display

Checks the current consumable counter values.

2.4.1.3.1

5.1 (ENG

STATUS

PRINT)

14 Menu setup

check

Displays the menu settings set on the printer
(CU).

2.4.1.3.2

Print a

configuration
report (Menu

Map) (refer

to User’s

Manual).

15 Print

information
check

Checks the Mac address and each firmware
version.

2.4.1.3.3

Print a

configuration
report (Menu

Map) (refer

to User’s

Manual).

16 Memory

value check

Checks the information on the CPU and memory
installed on the printer (CU).

2.4.1.3.4

Print a

configuration
report (Menu

Map) (refer

to User’s

Manual).

17 Test print

Executes the local print function and sends a
specified file.
Purpose: To check the printer on a stand-alone
basis and send a download file.

2.4.1.4.1

Perform local

printing (refer

to System

Specification).

18 Switch scan

test

Executes the switch scan test.
Purpose: To check each sensor for proper
operation.

2.4.1.5.1

19 Motor clutch

test

Executes the motor clutch test.
Purpose: To check each item, such as a motor
or clutch, for proper operation.

2.4.1.5.2

Option

Adjustment

Section in

Maintenance

Utility

operation

manual

Operation from

operator panel

(section in this

maintenance

manual)

20 Color

registration
adjustment
test

Executes the color registration adjustment test.

2.4.1.5.3

21 Density

adjustment
test

Executes the density adjustment test.

2.4.1.5.4

22 Auto density

adjustment
control
parameter
setting
(must not
be used)

Sets the auto density setting control parameter.

Never use

this option.

23 Counter

display

Checks the consumable, continuous
consumable and waste toner counter values.

2.4.1.5.6

24 Local

parameter
setting

Switches between the Factory and Shipping
modes and checks the status of the fuse.

2.4.1.5.7

25 Engine

parameter
setting

Makes an engine parameter setting.

2.4.1.5.8

26 Media

transfer
parameter
setting

Makes a print media transfer parameter setting.

2.4.1.5.9

Note! Do not operate or set options marked with ‘Never use this option’, or a

malfunction is potentially caused.

Summary of Contents for C810






























































































































































































































































Search results

Summary of Contents for C810

Reviews:

Oki C810, Maintenance Manual, Page: 124 / 253

Search results

Summary of Contents for C810

Reviews: