manualshive.com logo in svg

Oki C810, Maintenance Manual, Page: 174 / 253

Share
Download
Oki C810 Maintenance Manual Download Page 174

44015503TH  Rev. 1 

173 /

Oki  Data  CONFIDENTIAL

7.  TROUBLESHOOTING PROCEDURE

Display on operator panel

ON

LINE
lamp

Inspec-

tion

lamp

Contents

Code

nnn

Wait for a while.

Program data is being 
written.

Off

Blink

Indicates that the NIC program data to be 
updated is being written. 

Error

Reboot the printer. 

Writing of Program data is 
complete. 

Off

Off

Indicates that the writing of NIC program data to 
be updated is complete. 

Error

Check the data. 

Program data written error

%DLCODE%

Off

On

Indicates that error has occurred during the 
writing of NIC program data receiving that is to 
be updated. 

%DLCODE%

1: Memory allocation error

2: Download file error

3: Device free space acquisition error

4: Device insufficient free space error

5: File write error

6: CU-F/W mismatch error

Error

Wait for a while. 

The printer is restarting. 

%CODE%

Off

On

Indicates that the controller unit is being reboot. 

%CODE% is a decimal value (single digit) 
indicating cause of the reboot.

=0....Reboot that is resulted from a cause 

other than the below.

=1....Reboot by the PJL command

=2....Reboot caused by the menu change 

=3....Reboot based on quit operator of 

PostScript Language 

=4....Reboot caused by the network utilities 

(including web)

Error

The printer is shutting down. 

Off

Off

Indicates that a printer is shutting down.

The shut-down process is started by pressing 
the BACK button for more than 4 seconds upon 
completion of printer initialization process.

Error

Shutdown is completed. 

Shut off the Electric power or 
reboot it by restart button. 

Off

Off

Indicates that the shut-down process of a printer 
is complete. (The LCD backlight turns off.)

Error

Shut off the Electric power 
and wait for a while. 

126: The printer is 
condensing.

Off

Blink

Dew condensation error  (This error is handled 
in the same way as the service call error though 
display only is different.)

Fatal 

126

Display on operator panel

ON

LINE
lamp

Inspec-

tion

lamp

Contents

Code

nnn

Reboot the printer. 

%ERRCODE%: Error

Off

Blink

Indicates that a fatal error has occurred. 

For details refer to “Service call error list”.

Fatal 

<nnn>

Contact the Service center. 

%ERRCODE%: Error

Off

Blink

Indicates that a fatal error has occurred. 

For details refer to “Service call error list”.

Fatal 

<nnn>

Contact the Service center. 

%ERRCODE%: Error

Off

Blink

Indicates that a fatal error has occurred. 

For details refer to “Service call error list”. 

"*" indicates the detailed information of error. 

Fatal 

096 
231 
128 
168 
169

Power Off/On

%ERRCODE%:Fatal error

PC:nnnnnnnn

LR:nnnnnnnn

FR:nnnnnnnn

Off

Blink

Indicates that a fatal error has occurred. 

For details refer to “Service call error list”. 

"nnnnnnnn" indicates the detailed information of 
error. 

Fatal 

002 to  

011, 
F0C 
F0D 
FFE 

FFF

Reboot the printer. 

209: Download error

Off

Blink

Indicates failure of the Media table downloading 
to PU. (Custom Media Type related)

Fatal 

209

Summary of Contents for C810






























































































































































































































































Reviews:

No comments