manualshive.com logo in svg

Oki C810, Maintenance Manual, Page: 202 / 253

Share
Download
Oki C810 Maintenance Manual Download Page 202

44015503TH  Rev. 1 

201 /

Oki  Data  CONFIDENTIAL

7.  TROUBLESHOOTING PROCEDURE

(8-3)  Two-sided printing jam occurs in the process of reversing paper.

Check item

Check work

Action to be taken 

at NG

(8-3-1) Sensor lever operation check

Dup-IN sensor lever

Open the rear cover. Touch the Dup-IN sensor 
lever to check if its movement is unsmooth or 
not.

 Replace the 
Dup-IN sensor 
lever

DUP-IN sensor

Confirm that the sensor signals are normally 
detected by using the SWITCH SCAN function 
of the self-diagnostic mode.

Replace the 
Duplex board 
(v7y PCB), 
or replace the 
defective sensor 
or connection 
cable.

(8-3-2) Motor operation check

 Duplex motor

Check if the paper reversing operation is started 
or not by visual inspection when viewing through 
slit of the rear cover. 
If the paper reversing operation is not started, 
check if movement of the planetary gear inside 
the Duplex unit is unsmooth or not.

 Replace the 
planetary gear.

(8-4)  Two-sided printing jam occurs during transporting paper inside the Duplex unit.

Check item

Check work

Action to be taken 

at NG

(8-4-1) Sensor lever operation check

Dup-R, Dup-F 
sensor lever

Remove the Duplex unit and check movement of 
the sensor lever.

Replace the 
sensor lever.

 (8-4-2) Sensor check

Check the detection 
condition of the 
sensor signal

Confirm that the sensor signals are normally 
detected by using the SWITCH SCAN function 
of the self-diagnostic mode. 
For all sensors except the Dup-IN sensor, check 
the detection condition of the respective sensor 
in the two status: One is the status in which 
paper remains inside the Duplex unit. The other 
is the status in which paper is removed from the 
Duplex unit.

 Replace the 
Duplex board 
(v7y PCB), 
or replace the 
defective sensor 
or connection 
cable. 

(8-5)  Paper is not supplied from the Duplex unit to the regist roller.

Check item

Check work

Action to be taken 

at NG

(8-5-1) Clutch operation check

Duplex clutch

Confirm that the Duplex clutch works normally 
by using the Motor & Clutch Test of the self-
diagnostic mode.Confirm it by listening to the 
sound. 

Replace the 
v7y board or 
clutch.

Summary of Contents for C810






























































































































































































































































Reviews:

No comments