Oki C810 Maintenance Manual Download Page 60

Page: 60 / 253

44015503TH Rev. 1

59 /

Oki Data CONFIDENTIAL

3. INSTALLATION

<Ethernet cable connection>

Note! Refer to the user’s manual for operating environment.

Preparing an Ethernet cable

Note! An Ethernet cable and a hub do not come with the printer. Ask the user to

prepare an Ethernet cable (a Category 5 twisted pair cable, straight through)

and a hub.

Memo For the setup procedure of the printer driver, see the user’s manual.

Network interface connector

switching off the printer and the computer

Connecting the computer to the printer

(1) Plug the Ethernet cable into the network interface connector of the printer.

(2) Plug the Ethernet cable into the hub.

<Hub>

<Parallel connection>

Preparing a parallel cable

Note! A parallel cable does not come with the printer. Ask the user to prepare a

parallel cable.

turning off the printer and the computer.

Connecting the computer to the printer

(1) Connect a parallel cable to the parallel interface connector of the printer and lock

the cable with the metal fitting.

(2) Connect the parallel cable to the parallel interface connector of the computer and

tighten the cable clamp screws.

Parallel cable

Screw

Metal fitting

Summary of Contents for C810






























































































































































































































































Search results

Summary of Contents for C810

Reviews:

Oki C810, Maintenance Manual, Page: 60 / 253

Search results

Summary of Contents for C810

Reviews: