manualshive.com logo in svg

Oki C810, Maintenance Manual, Page: 184 / 253

Share
Download
Oki C810 Maintenance Manual Download Page 184

44015503TH  Rev. 1 

183 /

Oki  Data  CONFIDENTIAL

7.  TROUBLESHOOTING PROCEDURE

Check item

Check work

Action to be taken 

at NG

(2-2-3) Check the jumping phenomena of gear tooth. (Abnormal load of the consumable item)

Operating conditions 
of the respective 
motors

Check if operations of the respective motors are 
normal or not by using the self-diagnostic mode. 
Check if any load exists or not. 
"Buzz buzz" sound is generated when an error 
occurs.

Replace the 
corresponding 
consumable 
item. 
If any attempt 
of using new 
part as a trial 
is going to 
be made, be 
sure to use 
the System 
Maintenance 
Menu FUSE 
KEEP MODE.

Installation condition 
of each consumable 
item

Check by visual inspection if the respective 
consumable items are installed in their normal 
positions in which gears of the consumable 
items engage accurately or not.

Replace an 
appropriate 
mechanical part 
as required, or 
adjust or repair

(2-2-4) Check the wiring conditions of cables

Wiring conditions 
of the cables in 
the vicinity of the 
respective cooling 
fans

 Check if the cable contacts with the fan blade 
because wiring conditions of the cables near fan 
is poor or not. 
"Clap, clap" sound is generated when an error 
occurs.

 Correct the 
wiring conditions 
of the cable.

(2-2-5) Check installation condition of mechanical parts

Check the 
installation 
conditions of the 
partition plate under 
the CU and PU 
boards.

Remove the CU and PU board, and inspect the 
installation conditions of the partition plate by 
visual inspection.

 If they are not 
hooked on the 
normal specified 
positions, 
correct them.

(2-3)  Bad odors are generated.

Check item

Check work

Action to be taken 

at NG

(2-3-1) Locating the exact position of generating bad odor

Fuser unit

 Remove the fuser unit and check the odor. 

Implement 
section (2-3-2).

Low voltage power 
supply unit

Remove the low voltage power supply unit and 
check the odor.

Replace the low 
voltage power 
supply unit

(2-3-2) Check conditions of the fuser unit

Life count of fuser 
unit

 Check the life count of the fuser unit by using 
the self-diagnostic mode.

 The fuser close 
to the new fuser 
unit smells 
some odors.

Check that no 
foreign material 
exists in fuser unit.

Check that no foreign materials such as paper 
are stuck inside of the fuser unit.

Remove the 
foreign material.

(2-4)  Rise-up time is slow.

Check item

Check work

Action to be taken 

at NG

(2-4-1) Check the fuser unit

Halogen lamp

 

Check  that  100v  is  shown  on  the  label  on  the 
rear of the fuser unit.

 Replace the 
fuser unit.

(2-4-2) Check the optional parts   Note!

Add-on memory

Install the optional parts (add-on memory) again 
and re-check the operations.

 Replace the 
optional part.

HDD

Install the optional part (HDD) again and re-
check the operations.

 Replace the 
optional part.

Data Protection Kit  
-A1 

Refer to section 7.8.

Note!  If any troubles such as printer does not start up normally occurs, remove the 

CU options (RAM, HDD) and check if the trouble symptom changes or not.

Summary of Contents for C810






























































































































































































































































Reviews:

No comments