manualshive.com logo in svg

Oki C810, Maintenance Manual, Page: 175 / 253

Share
Download
Oki C810 Maintenance Manual Download Page 175

44015503TH  Rev. 1 

174 /

Oki  Data  CONFIDENTIAL

7.  TROUBLESHOOTING PROCEDURE

Table 7-1-2  Service Call Error List

Display

Cause

Error details

Remedial measure

Contact the Service 
center.
001: Error

Machine 
Check 
Exception

Replace CU board

Reboot the printer. 
002: Error
   ~
007: Error

CPU 
Exception

 
 
 

Does the error display recur?

 
 
 

yes

No

If the RAM DIMM is 
installed, remove it and 
turn off the power of the 
printer and back on.

Replace the CU board.

Re-install the RAM DIMM.

Replace the RAM DIMM. 

Contact the Service 
center.
020: Error 

CU ROM Hash 
Check Error

 

Does the error display recur?

 

yes

Turn off the power of the 
printer and back on.

Replace the CU

Contact the Service 
center.
024: Error
025: Error

CU Font ROM 
Hash Check 
Error

 

Does the error display recur?

 

yes

Turn off the power of the 
printer and back on.

Replace the CU

Contact the Service 
center.
030: Error

CU RAM 
Check Error

 

Does the error display recur?

 

yes

Turn off the power of the 
printer and back on.

Replace the CU board.

Contact the Service 
center.
031: Error

CU Optional 
RAM Check 
Error

Is installation of the RAM 
DIMM normal?

Does the printer recover from 
the error when the RAM DIMM 
is replaced?

No 

yes

No

Re-install the RAM DIMM. 

Replace the RAM DIMM.

Replace the CU board.

Contact the Service 
center.
036: Error

Slot1 RAM 
Spec Error

Is installation of the RAM 
DIMM normal?

Does the printer recover from 
the error when the RAM DIMM 
is replaced?

No

 

yes 

No

Re-install the RAM DIMM. 

Replace the RAM DIMM.

Replace the CU board.

Contact the Service 
center.
040: Error

CU EEPROM 
Error

 

Does the error display recur?

 

yes

Turn off the power of the 
printer and back on.

Replace the CU board.

Contact the Service 
center.
041: Error

CU Flash 
Error.

Flash ROM 
Error on the 
CU board.

 

Does the error display recur?

 

yes 

Turn off the power of the 
printer and back on.

Replace the CU board.

Display

Cause

Error details

Remedial measure

Contact the Service 
center.
042: Error
043: Error
   ~
045: Error

Flash File 
System Error

Failed to access to the Flash 
ROM that is directly soldered 
to the CU board.

Turn off the power of the 
printer and back on.

Replace the CU board.

Contact the Service 
center.
051: Error

CU Fan Error

Reboot the printer. 
052: Error

Image 
Processor 
Driver Error

Turn the printer power off 
and then back on.

If the error symptom 
remains unchanged, 
replace the CU board.

Reboot the printer.
070: Error 

PostScript 
Internal Error

Turn power to OFF/ON.

Reboot the printer.
072: Error - xx

Engine I/F 
Error.

I/F error 
between PU 
and CU

Is the CU assembly installed 
normally?

Does the printer recover from 
the error when the CU board is 
replaced?

No

 

yes

No

Re-install the CU 
assembly normally.

Replace the CU board.

Replace the PU Board.

Restart the printer.
073: Error xxxxxxxx

video Error

Error is 
detected when 
expanding the 
video data.

(Illegal data is 
received.)

Is the CU assembly installed 
normally? 

 
 
 
 
 

Does this error recur?

No

 

yes 

 
 
 

 

yes

Re-install the CU 
assembly normally.

Change the PC with 
another PC having 
high specifications, 
or alternately reduce 
resolution power and 
execute the print again.

Replace the CU board.

Replace the interface 
cable.

Re-install the PC Printer 
driver. 

Is the CU assembly installed 
normally?

Does this error recur? 

Does the error depend on print 
Data?

No 

yes

yes

No

yes

Re-install the CU 
assembly normally.

Execute the print again.

Print any other data.

Replace the CU board.

Send the data to design 
division and request 
analysis of the data. 

Summary of Contents for C810






























































































































































































































































Reviews:

No comments