Oki C810 Maintenance Manual Download Page 22

Page: 22 / 253

44015503TH Rev. 1

21 /

Oki Data CONFIDENTIAL

2. DESCRIPTION OF OPERATION

2.2 Printing process

The paper fed from Tray 1 or Tray 2 is carried by the paper feed roller, the registration roller L, and

the transport roller. When the paper is fed from the MPT, it is carried by the MPT paper feed roller

and the registration roller U. Then, an unfixed toner image is created on the paper transported

onto the belt sequentially through the electrophotographic process of KyMC. Thereafter, the

image is fixed under heat and pressure as the paper goes through the fuser unit. After the image

has been fixed, the paper is ejected to a face-up stacker or to a face-down stacker, according to

the outputting method selected by opening or closing of the face-up stacker.

While the above refers to the one-sided print operation of the printer, its operation in two-

sided print will be explained below.

When two-sided print is conducted, the paper that has passed through the fuser unit following

first one-sided print is sucked into the Duplex unit by the separator DUP. After entering the paper

reverse transport path, the paper is carried from there to the inside of the Duplex unit by the

inverting operation of the reverse roller. Then, after passed through the Duplex unit by the transport

roller that is located on the transport path inside the Duplex unit, the paper is fed along the paper

feed route of the Duplex unit to eventually merge the same route that comes from the tray. From

here on, the same operation as that of one-sided print of paper fed from the tray takes place.

Face-do

wn stac

ker

Face-up stac

ker

MPT

Sub-roller

Paper feed roller

Sub-roller

Transport roller

Paper feed roller

Registration roller L

Registration roller U

MPT paper feed roller

Transport belt

Transport roller

Reverse roller

Separator DUP

Heat roller

Backup roller

Halogen lamp

Paper reverse transport path

(1) Paper fed from 1st Tray

1. As illustrated in Figure 2-1, when the solenoid is ON, the registration motor

rotates (counterclockwise), transporting the paper until the IN1 sensor comes

ON. (When the solenoid is ON, the paper feed roller is driven.)

2. After causing the IN1 sensor to come ON, the paper is further carried over a

certain distance to finally hit the registration roller L. (This corrects skew of the

paper.)

3. As shown in Figure 2-2, the solenoid is turned OFF, and the paper is carried by

the registration roller L. (When the solenoid is OFF, the registration roller L is

driven.)

Registration roller U

(drive)

Registration roller U

(drive)

Hopping roller (drive)

Hopping roller (stop)

Paper

Sub-roller

(drive)

Sub-roller

(stop)

Registration motor

(counterclockwise)

Registration motor

(counterclockwise)

Registration roller L

(stop)

Registration roller L

(drive)

WR sensor

Solenoid lever

(solenoid: ON)

Solenoid lever

(solenoid: OFF)

Hopping gear Assy

IN2 sensor

IN1 sensor

Figure 2-1

Figure 2-2

Summary of Contents for C810






























































































































































































































































Search results

Summary of Contents for C810

Reviews:

Oki C810, Maintenance Manual, Page: 22 / 253

Search results

Summary of Contents for C810

Reviews: