manualshive.com logo in svg

Oki C810, Maintenance Manual, Page: 30 / 253

Share
Download
Oki C810 Maintenance Manual Download Page 30

44015503TH  Rev. 1 

29 /

Oki  Data  CONFIDENTIAL

2.  DESCRIPTION OF OPERATION

Counter specifications

Total page count

MPT page count Tray 1 page count Tray 2 page count Tray 3 page count

Color page count

Monochrome page count

Description 

Total number of 

prints

Number of print 

media hopped 

from MPT

Number of print 

media hopped 

from Tray 1

Number of print 

media hopped 

from Tray 2

Number of print 

media hopped 

from Tray 3

Total number of color prints

Total number of monochrome 

prints

Count method: A4-basis 

or size independence 

Count up after 

passing the writing 

sensor

Count up if MPF 

(MPT) hopping 

is finished 

successfully 

Count up if Tray 1 

hopping is finished 

successfully 

Count up if Tray 2 

hopping is finished 

successfully 

Count up if Tray 3 

hopping is finished 

successfully 

The number of print media 

passing the fuser in color 

mode is counted when each 

job is finished. (1*)

The value is counted on an 

A4/Letter basis. Refer to 

A4/Letter conversion table (on 

the next page).

The number of print media 

passing the fuser in monochrome 

mode is counted when each job 

is finished. (1*)

Printing speed for color mode 

may be applied to monochrome 

mode. The value is counted on 

an A4/Letter basis. Refer to A4/

Letter conversion table (on the 

next page).

Operation when paper 

has jammed 

Printed pages are not counted when a paper feed (hopping) jam or a feed jam (380) occurs. 

Printed pages are counted when any jam except the said jams occurs. 

Since the total number of prints is counted up when the front end of print media passes the writing 

sensor, a feed jam (380) is also included into the limits for counted according to its jam type.  

Printed pages are not counted if paper jams before passing the 

fuser. They are counted if prints jam after passing the fuser.  

Operation for Duplex

Front/back count 

(+2) 

Only front count (+1)

The count increases by two. 

If a color page and a monochrome page exist in a pair of two 

pages, the color page count increases by two. If no color page 

exits in a pair of two pages, the monochrome page count 

increases by two. 

Reset condition

None

None

(1)  Replacement of ROM with another one of a different version. 

(2)  Change of the shipping destination 

(3)  Running of MENU RESET of the system maintenance menu

(4)  Replacement of a CU board

value storage destination

PU

PU

PU

PU

PU

CU

CU

Menu/MenuMap output

EngineMenuMap output

 (*2)

 (*2)

 (*2)

 (*2)

−

−

*1.  The count is not updated if the power is turned off when a paper jam occurs.

*2.  EngineMenuMap outputs Engine Menu Print (the first page) and Engine EEPROM Dump Print (the last page), and the number of sheets of paper fed from each tray is described only in the latter one (Dump 

page only). 

Summary of Contents for C810






























































































































































































































































Reviews:

No comments