
FTMx_MODE field descriptions
Field
Description
31–8
Reserved
This field is reserved.
This read-only field is reserved and always has the value 0.
7
FAULTIE
Fault Interrupt Enable
Enables the generation of an interrupt when a fault is detected by FTM and the FTM fault control is
enabled.
0
Fault control interrupt is disabled.
1
Fault control interrupt is enabled.
6–5
FAULTM
Fault Control Mode
Defines the FTM fault control mode.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
00
Fault control is disabled for all channels.
01
Fault control is enabled for even channels only (channels 0, 2, 4, and 6), and the selected mode is
the manual fault clearing.
10
Fault control is enabled for all channels, and the selected mode is the manual fault clearing.
11
Fault control is enabled for all channels, and the selected mode is the automatic fault clearing.
4
CAPTEST
Capture Test Mode Enable
Enables the capture test mode.
This field is write protected. It can be written only when MODE[WPDIS] = 1.
0
Capture test mode is disabled.
1
Capture test mode is enabled.
3
PWMSYNC
PWM Synchronization Mode
Selects which triggers can be used by MOD, CnV, OUTMASK, and FTM counter synchronization. See
. The PWMSYNC bit configures the synchronization when SYNCMODE is 0.
0
No restrictions. Software and hardware triggers can be used by MOD, CnV, OUTMASK, and FTM
counter synchronization.
1
Software trigger can only be used by MOD and CnV synchronization, and hardware triggers can only
be used by OUTMASK and FTM counter synchronization.
2
WPDIS
Write Protection Disable
When write protection is enabled (WPDIS = 0), write protected bits cannot be written. When write
protection is disabled (WPDIS = 1), write protected bits can be written. The WPDIS bit is the negation of
the WPEN bit. WPDIS is cleared when 1 is written to WPEN. WPDIS is set when WPEN bit is read as a 1
and then 1 is written to WPDIS. Writing 0 to WPDIS has no effect.
0
Write protection is enabled.
1
Write protection is disabled.
1
INIT
Initialize The Channels Output
When a 1 is written to INIT bit the channels output is initialized according to the state of their
corresponding bit in the OUTINIT register. Writing a 0 to INIT bit has no effect.
The INIT bit is always read as 0.
0
FTMEN
FTM Enable
This field is write protected. It can be written only when MODE[WPDIS] = 1.
Table continues on the next page...
Chapter 39 FlexTimer Module (FTM)
K22F Sub-Family Reference Manual, Rev. 4, 08/2016
NXP Semiconductors
913
Summary of Contents for K22F series
