Home
/
NXP Semiconductors
/
K22F series
/
Reference Manual

NXP Semiconductors K22F series, Reference Manual, Page: 506 / 1407

Share

Page: 506 / 1407

NXP Semiconductors K22F series Reference Manual Download Page 506

Should a dynamic scatter/gather attempt fail, setting the TCD.d_req bit will prevent a
future hardware activation of this channel. This stops the channel from executing
with a destination address (daddr) that was calculated using a scatter/gather address
(written in the next step) instead of a dlast final offest value.

3. Write the TCD.dlast_sga field with the scatter/gather address.
4. Write 1b to the TCD.e_sg bit.
5. Read back the 16 bit TCD control/status field.
6. Test the TCD.e_sg request status and TCD.major.linkch value:

If e_sg = 1b, the dynamic link attempt was successful.

If e_sg = 0b and the major.linkch (ID) did not change, the attempted dynamic link
did not succeed (the channel was already retiring).

If e_sg = 0b and the major.linkch (ID) changed, the dynamic link attempt was
successful (the new TCD’s e_sg value cleared the e_sg bit).

22.5.7.3.2 Method 2 (channel using major loop channel linking)

For a channel using major loop channel linking, the coherency model described here may
be used for a dynamic scatter/gather request. This method uses the TCD.dlast_sga field as
a TCD indentification (ID).

1. Write 1b to the TCD.d_req bit.

Should a dynamic scatter/gather attempt fail, setting the d_req bit will prevent a
future hardware activation of this channel. This stops the channel from executing
with a destination address (daddr) that was calculated using a scatter/gather address
(written in the next step) instead of a dlast final offest value.

2. Write theTCD.dlast_sga field with the scatter/gather address.
3. Write 1b to the TCD.e_sg bit.
4. Read back the TCD.e_sg bit.
5. Test the TCD.e_sg request status:

If e_sg = 1b, the dynamic link attempt was successful.

If e_sg = 0b, read the 32 bit TCD dlast_sga field.

If e_sg = 0b and the dlast_sga did not change, the attempted dynamic link did not
succeed (the channel was already retiring).

Initialization/application information

K22F Sub-Family Reference Manual, Rev. 4, 08/2016

506

NXP Semiconductors

«
...
504
505
506
507
508
...
»

Summary of Contents for K22F series
































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments