Mercedes-Benz C 240 Operator'S Manual Download Page 386

Page: 386 / 482

384

Practical hints

Unlocking/locking in an emergency

Fuel filler flap

In case the central locking system does
not release the fuel filler flap, you can open
it manually.

왘

Open the tailgate.

왘

Press button

왘

Fold down trim panel

왘

Reach inside through opening

direction of arrow.

왘

Turn release knob

clockwise

(arrow).

The fuel filler flap can now be opened.

Manually unlocking the transmission
gear selector lever

In the case of power failure the transmis-
sion gear selector lever can be manually
unlocked, e.g. to tow the vehicle.

왘

Slide out the swiveling cup holder
(

컄

page 260).

Tool

왘

Insert a tool

(e.g. flat blade

screwdriver) into the opening.

왘

Perform the following two steps
simultaneously:

왘

Press tool

forward in the

direction of arrow.

왘

Move gear selector lever from
position

왘

Remove tool

from the opening.

Warning!

If you operate the emergency release
button, be careful of the sharp edges so that
you do not injure yourself.

The gear selector lever is locked again
when moving it to position

Summary of Contents for C 240



































































































































































































































































































































































































































































































Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands

Mercedes-Benz C 240, Operator'S Manual

Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands