Mercedes-Benz C 240 Operator'S Manual Download Page 206

Page: 206 / 482

204

Controls in detail

Audio system

Adjusting treble

왘

Press

button repeatedly until

TREBLE

appears in the display.

왘

Press

–

soft key to increase or

decrease tone level accordingly.

왘

Press

RES

soft key briefly to reset treble

tones to their center level.

The radio switches back to the
standard radio menu eight seconds
after the last soft key is pressed.

Sound system*

You can either program the sound settings
manually (

컄

page 203) or choose settings

via preset sound characteristics.

You can select from among the following
settings:

앫

STANDARD

: conventional stereo sound.

앫

SURROUND

: the sound is set for better

three-dimensional acoustic character-
istics.

앫

SPEECH

: the sound is optimized for the

spoken word.

왘

Press

button repeatedly until

STANDARD

SURROUND

, or

SPEECH

appears

in the display.

왘

Press

soft key repeatedly

until the desired sound setting has
been reached.

The sound is set accordingly.

왘

Press

RES

soft key briefly.

The sound setting is reset depending
on the sound source activated.

앫

Radio mode:

STANDARD

앫

CD/AUX mode:

SURROUND

앫

Telephone:

SPEECH

The radio switches back to the
standard radio menu eight seconds
after the last soft key is pressed.

Summary of Contents for C 240



































































































































































































































































































































































































































































































Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands

Mercedes-Benz C 240, Operator'S Manual

Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands