Mercedes-Benz C 240 Operator'S Manual Download Page 151

Page: 151 / 482

149

Controls in detail

Control system

Setting the date (year)

This function can only be seen with audio
system.

왘

Move the selection marker with
button

to the

Time/Date

submenu.

왘

Press button

repeatedly

until the message

Date Set YY

appears

in the multifunction display.

The selection marker is on the year
setting.

왘

Press button

to set the

year.

Lighting submenu

Access the

Lighting

submenu via the

Settings

menu. Use the

Lighting

submenu to change the lamp and lighting
settings on your vehicle.

The following functions are available:

Vehicles with COMAND*:
For information on setting the date,
refer to the separate COMAND
operating instructions.

Function

Page

Setting daytime running lamp
mode (USA only)

150

Setting locator lighting

151

Setting night security
illumination

151

Setting interior lighting delayed
shut-off

153

Summary of Contents for C 240



































































































































































































































































































































































































































































































Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands

Mercedes-Benz C 240, Operator'S Manual

Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands