Mercedes-Benz C 240 Operator'S Manual Download Page 176

Page: 176 / 482

174

Controls in detail

Good visibility

Sun visors

The sun visors protect you from sun glare
while driving.

왘

Swing sun visors down when you
experience glare.

Mounting

Mirror cover

Mirror lamp

Sun visor

왘

To use illuminated mirror, lift up
cover

Warning!

Do not use the vanity mirror while driving.

Keep the mirrors in the sun visors closed
while vehicle is in motion. Reflected glare
can endanger you and others.

If sunlight enters through a side
window, disengage sun visor from
mounting

and pivot to the side.

The mirror lamp

will switch off.

Summary of Contents for C 240



































































































































































































































































































































































































































































































Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands

Mercedes-Benz C 240, Operator'S Manual

Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands