Mercedes-Benz C 240 Operator'S Manual Download Page 100

Page: 100 / 482

Controls in detail

Locking and unlocking

Factory setting

Global unlocking

왘

Press button

All turn signal lamps flash once. The
locking knobs in the doors move up.
The anti-theft alarm system* is
disarmed.

The vehicle will lock again automatically
and reactivate the anti-theft alarm
system* within approximately 40 seconds
of unlocking if:

앫

neither door nor tailgate is opened

앫

the SmartKey is not inserted in the
starter switch

앫

the central locking switch is not
activated

Global locking

왘

Press button

‹

All turn signal lamps flash three times.
The locking knobs in the doors move
down. The anti-theft alarm system* is
armed.

Selective setting

If you frequently travel alone, you may wish
to reprogram the SmartKey so that
pressing

only unlocks the driver’s

door and the fuel filler flap.

왘

Press and hold buttons

and

‹

simultaneously for about five seconds
until battery check lamp

flashes

twice.

The SmartKey will then function as
follows:

Unlocking driver’s door and fuel filler
flap

왘

Press button

once.

All turn signal lamps flash once. The
locking knob in the driver’s door moves
up. The anti-theft alarm system* is
disarmed.

Global unlocking

왘

Press button

twice.

All turn signal lamps flash once. The
locking knobs in the doors move up.
The anti-theft alarm system* is
disarmed.

Summary of Contents for C 240



































































































































































































































































































































































































































































































Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands

Mercedes-Benz C 240, Operator'S Manual

Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands