Mercedes-Benz C 240 Operator'S Manual Download Page 127

Page: 127 / 482

125

Controls in detail

Instrument cluster

왔

Instrument cluster

For a full view illustration of the instrument
cluster, see “At a glance” (

컄

page 24).

Reset button

The instrument cluster is activated when
you

앫

open a door

앫

switch on ignition

앫

press reset button

앫

switch on the exterior lamps

You can change the instrument cluster
settings in the Instrument cluster submenu
of the control system (

컄

page 143).

Instrument cluster illumination

Use reset button

to adjust the

illumination brightness for the instrument
cluster.

To brighten illumination

왘

Turn reset button

clockwise.

The instrument cluster illumination will
brighten.

To dim illumination

왘

Turn reset button

counterclock-

wise.

The instrument cluster illumination will
dim.

The instrument cluster illumination is
dimmed or brightened automatically to
suit ambient light conditions.

The instrument cluster illumination will
also be adjusted automatically when
you switch on the vehicle’s exterior
lamps.

Summary of Contents for C 240



































































































































































































































































































































































































































































































Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands

Mercedes-Benz C 240, Operator'S Manual

Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands