Mercedes-Benz C 240 Operator'S Manual Download Page 244

Page: 244 / 482

242

Controls in detail

Power windows

왘

Aim transmitter eye at the driver’s door
handle.

Opening (Summer opening feature)

왘

Press and hold button

after

unlocking the vehicle.

The windows and tilt/sliding sunroof*
begin to open after approximately one
second.

왘

Release the

button to stop

procedure.

Closing (Convenience feature)

왘

Press and hold button

‹

after

locking the vehicle.

The windows and tilt/sliding sunroof*
begin to close after approximately one
second.

왘

Release the

‹

button to stop

procedure.

Make sure all side windows and the
tilt/sliding sunroof* are properly closed
before leaving the vehicle.

Synchronizing power windows

The power windows must be
resynchronized each time

앫

after the battery has been
disconnected.

앫

if the power windows cannot be fully
opened (Express-open) or closed
(Express-close).

왘

Switch on ignition (

컄

page 33).

왘

Pull the power window switches until
the side windows are closed.

Hold the switches for approximately
one second.

The power windows are synchronized.

Summary of Contents for C 240



































































































































































































































































































































































































































































































Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands

Mercedes-Benz C 240, Operator'S Manual

Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands