Mercedes-Benz C 240 Operator'S Manual Download Page 158

Page: 158 / 482

156

Controls in detail

Control system

왘

Press button

to set

key-dependency

Off

Setting parking position* for exterior
rear view mirror

Use the

Mirror set. parking aid

function

to select whether the passenger-side
exterior rear view mirror should be turned
downward during parking maneuvers when
reverse gear

is engaged. For additional

information, see “Activating exterior rear
view mirror parking position*”
(

컄

page 173).

왘

Move the selection marker with
button

to the

Convenience

submenu.

왘

Press button

repeatedly

until the message

Mirror set.

parking aid

appears in the

multifunction display.

The selection marker is on the current
setting.

왘

Press button

to switch

function

Off

Trip computer menu

Use the trip computer menu to call up
statistical data on your vehicle.

The following information is available:

Function

Page

Fuel consumption statistics after
start

157

Fuel consumption statistics
since last reset

157

Calling up range
(distance to empty)

158

컄컄

Summary of Contents for C 240



































































































































































































































































































































































































































































































Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands

Mercedes-Benz C 240, Operator'S Manual

Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands