Mercedes-Benz C 240 Operator'S Manual Download Page 152

Page: 152 / 482

150

Controls in detail

Control system

Setting daytime running lamp mode
(USA only)

왘

Move the selection marker with
button

to the

Lighting

submenu.

왘

Press button

repeatedly

until the message

Hdlamp mode

appears

in the multifunction display.

The selection marker is on the current
setting.

왘

Press button

to select

manual operation (

Manual

) or daytime

running lamp mode (

Constant

)

activated.

With daytime running lamp mode activated
and the exterior lamp switch in
position

, the low beam

headlamps are switched on when the
engine is running.

In low ambient light conditions the
following lamps will switch on additionally:

앫

Parking lamps

앫

Tail lamps

앫

License plate lamps

앫

Side marker lamps

For more information on the daytime
running lamp mode, see “Lighting”
(

컄

page 116).

This function is not available in
countries where the daytime running
lamp mode is mandatory and therefore
in a constant mode.

For safety reasons, resetting the

Lighting

submenu to factory settings

(

컄

page 141) while driving will not

deactivate the daytime running lamp
mode.

The following message appears in the
multifunction display:

Lighting - Cannot be completely
reset to factory sets. while
driving.

Summary of Contents for C 240



































































































































































































































































































































































































































































































Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands

Mercedes-Benz C 240, Operator'S Manual

Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands