Mercedes-Benz C 240 Operator'S Manual Download Page 41 | Manualshive

Page: 41 / 482

background image

39

Getting started

Adjusting

Head restraint tilt

Manually adjust the angle of the head
restraint.

왘

Push or pull on the lower edge of the
head restraint cushion.

For more information, see “Seats”
(

컄

page 105).

Steering wheel

Warning!

G

For your protection, drive only with properly
positioned head restraints.

Adjust head restraint so that the center of
the head restraint supports the back of the
head at eye level. This will reduce the poten-
tial for injury to the head and neck in the
event of an accident or similar situation.

Do not drive the vehicle without the seat
head restraints. Head restraints are
intended to help reduce injuries during an
accident.

Warning!

G

Do not adjust the steering wheel while
driving. Adjusting the steering wheel while
driving, or driving without the adjustment
locked could cause the driver to lose control
of the vehicle.

When leaving the vehicle, always remove the
SmartKey from the starter switch, take it
with you, and lock the vehicle.

Even with the SmartKey removed from the
starter switch, the electrical steering wheel
adjustment feature* can be operated when
the driver’s door is open. Therefore, do not
leave children unattended in the vehicle, or
with access to an unlocked vehicle. Unsu-
pervised use of vehicle equipment may
cause an accident and/or serious personal
injury.

«
...
39
40
41
42
43
...
»

Summary of Contents for C 240



































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for C 240

Brand: Harken Hoister Pages: 12

Brand: Yamaha Pages: 2

Brand: Warrior Winches Pages: 17

Brand: Jackco Pages: 11

Retrotech RTX-68D-CHG

Brand: Dakota Digital Pages: 4

Brand: CITROEN Pages: 52

Brand: Victory 4x4 Pages: 13

Brand: Caltrend Pages: 2

Brand: Audiovox Pages: 1

EGR-3PVE-COLOUR

Brand: EGR Pages: 28

Brand: STARLANE Pages: 24

Park Vision VAL632210

Brand: Valeo Pages: 25

Brand: v.link Pages: 19

OUTLANDER PHEV 2022

Brand: Mitsubishi MOTORS Pages: 8

Brand: Gacell Pages: 25

Brand: Easee Pages: 21

SHERPA SADDLE BAG JL

Brand: Overland Outfitters Pages: 2

Electronic Parking Disc 3

Brand: Jacob Jensen Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands