Mercedes-Benz C 240 Operator'S Manual Download Page 35 | Manualshive

Page: 35 / 482

background image

33

Getting started

Unlocking

Starter switch positions

SmartKey

Starter switch

0

For removing SmartKey
The steering is locked when the
SmartKey is removed from the starter
switch. If necessary, move steering
wheel slightly to allow the locking
mechanism to engage.

1

Power supply to some electrical
consumers, such as seat adjustment

2

Ignition (power supply for all electrical
consumers) and driving position.
All lamps (except low beam headlamp
indicator lamp, high beam headlamp in-
dicator lamp, and turn signal indicator
lamps unless activated) in the instru-
ment cluster come on. If a lamp in the
instrument cluster fails to come on
when the ignition is switched on, have
it checked and replaced if necessary. If
a lamp in the instrument cluster re-
mains on after starting the engine or
comes on while driving, refer to “Lamps
in instrument cluster” (

컄

page 344).

3

Starting position

Warning!

G

When leaving the vehicle, always remove the
SmartKey from the starter switch, take it
with you, and lock the vehicle. Do not leave
children unattended in the vehicle, or with
access to an unlocked vehicle. Unsuper-
vised use of vehicle equipment may cause
an accident and/or serious personal injury.

«
...
33
34
35
36
37
...
»

Summary of Contents for C 240



































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for C 240

Brand: Yakima Pages: 4

Brand: Metra Electronics Pages: 2

Brand: Whispbar Pages: 15

Brand: PullRite Pages: 10

Brand: Toyota Pages: 371

signal mirror 2005-2009 Ford Mustang

Brand: muth Pages: 9

Brand: Metra Electronics Pages: 2

Brand: UAZ Pages: 112

GMC Yukon Denali 2005

Brand: Cadillac Pages: 456

Brand: Saab Pages: 63

Brand: R&G Pages: 20

Brand: Whispbar Pages: 70

Brand: Broadfeet Pages: 2

Brand: Prorack Pages: 15

Brand: Cadillac Pages: 20

Brand: Pyle Pages: 8

Brand: Lexus Pages: 82

Brand: Phonocar Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands