Mercedes-Benz C 240 Operator'S Manual Download Page 368 | Manualshive

Page: 368 / 482

background image

366

Practical hints

What to do if …

Display symbol

Display message

Possible cause

Possible solution

•

Coolant
Stop, engine off!

The poly-V-belt could be broken.

왘

Stop immediately and check the
poly-V-belt.

If it is broken:

왘

Do not continue to drive. Otherwise the
engine will overheat due to an inoperative
water pump which may result in damage to
the engine. Notify an authorized
Mercedes-Benz Center.

If it is intact:

왘

Do not continue to drive the vehicle with
this message displayed. Doing so could
result in serious engine damage that is not
covered by the Mercedes-Benz Limited
Warranty.

왘

Observe the coolant temperature gauge in
the instrument cluster (

컄

page 24).

왘

Drive immediately to the nearest authorized
Mercedes-Benz Center.

Coolant
Visit workshop.

The cooling fan for the coolant is
malfunctioning.

왘

Observe the coolant temperature gauge in
the instrument cluster (

컄

page 24).

왘

Have the fan replaced as soon as possible.

«
...
366
367
368
369
370
...
»

Summary of Contents for C 240



































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for C 240

Brand: Kargo Master Pages: 5

Brand: Aries Pages: 3

Brand: Suzuki Pages: 353

Brand: Torklift Pages: 16

Brand: Saab Pages: 445

Brand: muth Pages: 10

Brand: Thule Pages: 12

Brand: Mercedes-Benz Pages: 54

Brand: ideus Pages: 159

Brand: iArmor Pages: 6

2011 SRX CROSSOVER

Brand: Cadillac Pages: 416

Brand: TIE DOWN Pages: 2

Brand: Lantronix Pages: 51

Brand: BraunAbility Pages: 46

Brand: MiX Telematics Pages: 39

Brand: Black Horse Off Road Pages: 3

Brand: NavLinkz Pages: 26

VIEWLINE TEMPERATURE GAUGES

Brand: VDO Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands