Mercedes-Benz C 240 Operator'S Manual Download Page 349

Page: 349 / 482

347

Practical hints

What to do if …

Problem

Possible cause

Suggested solution

(USA only)

(Canada only)

The yellow engine malfunction
indicator lamp comes on while
driving.

A loss of pressure has been
detected in the fuel system.
The fuel cap may not be closed
properly or the fuel system
may be leaky.

왘

Check the fuel cap (

컄

page 293).

If it is not closed properly:

왘

Close the fuel cap.

If it is closed properly:

왘

Have the fuel system checked by an
authorized Mercedes-Benz Center.

Your fuel tank is empty.

왘

After refuelling start, turn off and
restart the engine three or four times
in succession.

The limp-home mode is canceled. You do
not need to have your vehicle checked.

Summary of Contents for C 240



































































































































































































































































































































































































































































































Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands

Mercedes-Benz C 240, Operator'S Manual

Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands