Mercedes-Benz C 240 Operator'S Manual Download Page 357 | Manualshive

Page: 357 / 482

background image

355

Practical hints

What to do if …

Display message

Possible cause

Possible solution

Front-pass.
airbag activated
See Operator’s Manual

If performing any of the above corrective steps is
successful, the message

Front-pass. airbag

deactivated See Operator’s Manual

will

appear in the multifunction display, confirming
the situation has been remedied. Note that after
performing the corrective steps, it may take up
to 60 seconds for the message

Front-pass.

airbag deactivated See Operator’s Manual

to

appear.

If the message

Front-pass. airbag activated

See Operator’s Manual

remains on in the

multifunction display and/or the

56

indicator lamp remains out even after

performing the above corrective steps, have the
system checked as soon as possible by an
authorized Mercedes-Benz Center.

Warning!

G

If the message

Front-pass. airbag

activated See Operator’s Manual

remains on in the multifunction display
and/or the

56

indicator lamp

remains out even after performing the above
corrective steps, do not have any
children12 years old and under and other
small individuals use the front passenger
seat until the system has been repaired.

«
...
355
356
357
358
359
...
»

Summary of Contents for C 240



































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for C 240

Brand: Triumph Pages: 86

PRIME DESIGN VRI3-E-PM11

Brand: Safe Fleet Pages: 12

Brand: Axxess Pages: 4

Brand: Vintage Air Pages: 14

Brand: Quadratec Pages: 6

Sprinter Side Ladder

Brand: FVC Pages: 8

Brand: CSL Pages: 8

Brand: Kuda Pages: 3

Brand: Raider Pages: 2

EVO ONE THAR-GM7

Brand: Fortin Pages: 11

Brand: Alu-Cab Pages: 6

Brand: BrandMotion Pages: 9

Brand: Mercedes-Benz Pages: 108

Brand: Black & Decker Pages: 16

Brand: Black & Decker Pages: 27

Brand: Black & Decker Pages: 38

Brand: Black & Decker Pages: 12

Brand: Black & Decker Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands