Mercedes-Benz C 240 Operator'S Manual Download Page 378

Page: 378 / 482

376

Practical hints

What to do if …

Display symbol

Display message

Possible cause

Possible solution

Close slid./pop-up
sunroof

You have opened the driver’s door with
the SmartKey removed from the starter
switch and the tilt/sliding sunroof open.

왘

Close the tilt/sliding sunroof
(

컄

page 243).

Close slid./pop-up
sunroof

You have opened the driver’s door with
the SmartKey removed from the starter
switch and the tilt/sliding sunroof open.

왘

Close the tilt/sliding sunroof
(

컄

page 243).

Tele Aid malfunction.
Drive to workshop

One or more main functions of the Tele
Aid system* are malfunctioning.

왘

Have the Tele Aid system* checked by
an authorized Mercedes-Benz Center.

Function unavailable.

This display appears if button

on the multifunction steering

wheel is pressed and the vehicle is not
equipped with a telephone*.

Trunk open

This message will appear whenever the
tailgate is open.

왘

Close the tailgate.

Washer fluid
please refill

The fluid level has dropped to
about

of total reservoir capacity.

왘

Add washer fluid (

컄

page 303).

Summary of Contents for C 240



































































































































































































































































































































































































































































































Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands

Mercedes-Benz C 240, Operator'S Manual

Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands