Mercedes-Benz C 240 Operator'S Manual Download Page 242 | Manualshive

Page: 242 / 482

background image

240

Controls in detail

Power windows

왘

Switch on ignition (

컄

page 33).

Opening the windows

왘

Press switch

1

to

4

to the resistance

point.

The corresponding window will move
downwards until you release the
switch.

Closing the windows

왘

Pull switch

1

to

4

to the resistance

point.

The corresponding window will move
upwards until you release the switch.

Fully opening the windows
(Express-open)

왘

Press switch

1

to

4

past the

resistance point and release.

The corresponding window opens
completely.

Fully closing the windows
(Express-close)

왘

Pull switch

1

to

4

past the

resistance point and release.

The corresponding window closes
completely.

i

You can also open or close the
windows using the SmartKey (summer
opening/convenience closing feature)
(

컄

page 241).

You can close and reopen the windows
using the air recirculation button

,

in the climate control panel
(

컄

page 177) or automatic climate

control panel* (

컄

page 187).

You can close and reopen the windows
using the charcoal filter button

e

in

the automatic climate control panel*
(

컄

page 187).

Warning!

G

If you pull and hold the switch up when
closing the window, and upward movement
of the window is blocked by some obstruc-
tion including but not limited to arms, hands,
fingers, etc., the automatic reversal will not
operate.

«
...
240
241
242
243
244
...
»

Summary of Contents for C 240



































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for C 240

Brand: Lancia Pages: 386

Brand: Vauxhall Pages: 2

Brand: Volvo Pages: 10

Brand: Porsche Pages: 313

LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne...

Brand: Dakota Digital Pages: 3

Brand: Skoda Pages: 165

Brand: STARLANE Pages: 24

Brand: Volvo Pages: 266

Brand: Subaru Pages: 2

Brand: Subaru Pages: 328

Brand: Meta System Pages: 22

FXX ATM Emulator

Brand: BMW Pages: 5

Brand: Whispbar Pages: 15

TuneBase F8Z442

Brand: Belkin Pages: 162

1500 CLASSIC 2020

Brand: RAM Pages: 360

Sebring Convertible

Brand: Chrysler Pages: 454

Brand: Mercedes-Benz Pages: 24

Brand: Conrad Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands