Mercedes-Benz C 240 Operator'S Manual Download Page 372

Page: 372 / 482

370

Practical hints

What to do if …

Display symbol

Display message

Possible cause

Possible solution

Check gas cap.
See Operator’s Manual

A loss of pressure has been detected in
the fuel system. The fuel cap may not be
closed properly or the fuel system may be
leaky.

왘

Check the fuel cap (

컄

page 293).

If it is not closed properly:

왘

Close the fuel cap.

If it is closed properly:

왘

Have the fuel system checked by an
authorized Mercedes-Benz Center.

Hood open

You are driving with the hood open.

왘

Close the hood (

컄

page 296).

Remove key.

You have forgotten to remove the
SmartKey.

왘

Remove the SmartKey from the starter
switch.

Replace key
Drive to workshop

No additional code available for
SmartKey.

왘

Change the SmartKey.

Summary of Contents for C 240



































































































































































































































































































































































































































































































Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands

Mercedes-Benz C 240, Operator'S Manual

Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands