Mercedes-Benz C 240 Operator'S Manual Download Page 248

Page: 248 / 482

246

Controls in detail

Power tilt/sliding sunroof*

Closing (Convenience feature)

왘

Press and hold button

‹

after

locking the vehicle.

The windows and the tilt/sliding
sunroof begin to close after
approximately one second.

왘

Release the

‹

button to stop

procedure.

Make sure all side windows and the
tilt/sliding sunroof are properly closed
before leaving the vehicle.

Synchronizing the power tilt/sliding
sunroof

The tilt/sliding sunroof must be
synchronized

앫

after the battery has been
disconnected or discharged

앫

after the tilt/sliding sunroof has been
closed manually (

컄

page 385)

앫

after a malfunction

앫

if the tilt/sliding sunroof does not open
smoothly

왘

Switch on ignition (

컄

page 33).

왘

Move and hold the sunroof switch in
the direction of arrow

(

컄

page 243)

until the tilt/sliding sunroof is fully
raised at the rear.

Hold the sunroof switch for
approximately one second.

왘

Check the Express-open feature
(

컄

page 244).

If the tilt/sliding sunroof opens
completely, the tilt/sliding sunroof is
synchronized. Otherwise repeat the
above steps.

Summary of Contents for C 240



































































































































































































































































































































































































































































































Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands

Mercedes-Benz C 240, Operator'S Manual

Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands