Mercedes-Benz C 240 Operator'S Manual Download Page 380 | Manualshive

Page: 380 / 482

background image

378

Practical hints

Where will I find ...?

3

Vehicle tool kit

The following is included:

앫

Towing eye bolt

앫

Wheel wrench

앫

Alignment bolt

앫

Vehicle jack

앫

Spare wheel bolts

앫

Fuse extractor

앫

Spare fuses

앫

Collapsible wheel chock

앫

A pair of gloves

Vehicle jack

The vehicle jack is located in the storage
compartment behind the left trim panel.

Storage position

왘

Remove vehicle jack from its
compartment.

왘

Push crank handle up.

Warning!

G

The jack is designed exclusively for jacking
up the vehicle at the jack take-up brackets
built into both sides of the vehicle. To help
avoid personal injury, use the jack only to lift
the vehicle during a wheel change. Never
get beneath the vehicle while it is supported
by the jack. Keep hands and feet away from
the area under the lifted vehicle. Always
firmly set parking brake and block wheels
before raising vehicle with jack.

Do not disengage parking brake while the
vehicle is raised. Be certain that the jack is
always vertical (plumb line) when in use,
especially on hills. Always try to use the jack
on level surface. Make sure the jack arm is
fully seated in the jack take-up bracket.
Always lower the vehicle onto sufficient
capacity jackstands before working under
the vehicle.

«
...
378
379
380
381
382
...
»

Summary of Contents for C 240



































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for C 240

Green Motion DC 22

Brand: Eaton Pages: 65

2013 C-Class Coupe

Brand: Mercedes-Benz Pages: 388

Brand: Standby Pages: 10

Brand: Car-Interface Pages: 23

Brand: RuggON Pages: 2

Brand: DEFA Pages: 7

Brand: Prorack Pages: 15

Brand: Mercedes-Benz Pages: 373

Brand: Scion Pages: 24

Brand: MAcarbon Pages: 3

Brand: Sintrones Pages: 55

Brand: Blue Ox Pages: 5

Brand: Pyle Pages: 14

Brand: Buick Pages: 58

Brand: Buick Pages: 20

KY-700-2018-DRW01

Brand: FALCON RIDGE Pages: 7

PRIME DESIGN UXV 211

Brand: Safe Fleet Pages: 8

Brand: 3SIXT Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands