Mercedes-Benz C 240 Operator'S Manual Download Page 180 | Manualshive

Page: 180 / 482

background image

178

Controls in detail

Climate control

The climate control is operational when-
ever the engine is running. You can oper-
ate the climate control system in either the
automatic or manual mode. The system
cools or heats the interior depending on
the selected interior temperature and the
current outside temperature.

Nearly all dust particles, pollutants and
odors are filtered out before outside air en-
ters the passenger compartment through
the air distribution system.

The air conditioning will not engage
(no cooling) if mode

AC

OFF

is activated or

mode

A/C

is deactivated (

컄

page 183).

Warning!

G

When operating the climate control, the air
that enters the passenger compartment
through the air vents in the footwell can be
very hot or very cold (depending on the set
temperature). This may cause burns or frost-
bite on unprotected skin in the immediate
area of the air vents. Always keep sufficient
distance between unprotected parts of the
body and the footwell air vents. If necessary,
change the air flow using the air distribution
controls to direct the air away from the foot-
well air vents (

컄

page 180).

Warning!

G

Follow the recommended settings for heat-
ing and cooling given on the following pag-
es. Otherwise the windows could fog up,
impairing visibility and endangering you and
others.

i

Severe conditions (e.g. strong air
pollution) may require replacement of
the filter before its scheduled interval.
A clogged filter will reduce the air
volume to the interior.

If the vehicle interior is hot, ventilate
the interior before driving off, see
“Opening (Summer opening feature)”
(

컄

page 245).

Keep the air intake grille in front of the
windshield free of snow and debris.

«
...
178
179
180
181
182
...
»

Summary of Contents for C 240



































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for C 240

Brand: Baja Designs Pages: 6

Brand: Quadratec Pages: 8

Brand: T-Mobile Pages: 2

Brand: Ecco Pages: 24

Brand: Jaeger Pages: 11

Brand: Thule Pages: 4

Brand: Mitsubishi Pages: 362

Brand: HAKR Pages: 9

CF-UFORCE-DRW01

Brand: FALCON RIDGE Pages: 6

Brand: Meritor Pages: 20

SB-J-GCHER2/10W3v2

Brand: Stealthbox Pages: 2

Brand: Mercedes-Benz Pages: 305

S90 TWIN ENGINE

Brand: Volvo Pages: 662

Brand: Westfalia Pages: 2

PRIME DESIGN HRR-E-PM52

Brand: Safe Fleet Pages: 12

Brand: Rally Armor Pages: 4

Brand: Or-Fab Pages: 3

Brand: NavLinkz Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands