Mercedes-Benz C 240 Operator'S Manual Download Page 154

Page: 154 / 482

152

Controls in detail

Control system

왘

Move the selection marker with
button

to the

Lighting

submenu.

왘

Press button

repeatedly

until the message

Hdlamp delay off

appears in the multifunction display.

The selection marker is on the current
setting.

왘

Press button

to select

the desired lamp-on period.

You can select:

앫

0 sec.

, the delayed shut-off feature

is deactivated.

앫

15 sec.

30 sec.

45 sec.

60 sec.

, select the desired

lamp-on period.

왘

Turn the exterior lamp switch to
position

before turning off the

engine (

컄

page 116).

The headlamps delayed shut-off
feature is activated.

You can temporarily deactivate the
delayed shut-off feature:

왘

Before exiting the vehicle, turn the
SmartKey in the starter switch to
position

왘

Then turn it to position

and back to

position

The delayed shut-off feature is
deactivated. It will reactivate as soon
as you reinsert the SmartKey in the
starter switch.

You can reactivate this function within
ten minutes by opening a door.

Summary of Contents for C 240



































































































































































































































































































































































































































































































Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands

Mercedes-Benz C 240, Operator'S Manual

Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands