Mercedes-Benz C 240 Operator'S Manual Download Page 103

Page: 103 / 482

101

Controls in detail

Locking and unlocking

Front doors

왘

Pull on door handle

on the

respective front door to open door.

If door was locked, locking knob

will

move up.

Rear doors

왘

Pull up locking knob

on the

respective rear door to unlock door.

왘

Pull on door handle

on the

respective rear door to open door.

Opening the tailgate

A minimum height clearance of 6.40 ft
(1.95 m) is required to open the tailgate.

The handle is located above the rear
license plate recess.

Handle

The vehicle must be unlocked.

왘

Pull on handle

왘

Lift the tailgate.

Closing the tailgate

Handle

왘

Lower tailgate by pulling firmly on
handle

왘

Close tailgate with hands placed flat on
the tailgate.

Always make sure there is sufficient
overhead clearance.

Summary of Contents for C 240



































































































































































































































































































































































































































































































Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands

Mercedes-Benz C 240, Operator'S Manual

Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands