Mercedes-Benz C 240 Operator'S Manual Download Page 129 | Manualshive

Page: 129 / 482

background image

127

Controls in detail

Instrument cluster

Trip odometer

왘

Make sure you are viewing the trip
odometer and main odometer in the
multifunction display (

컄

page 129).

왘

If it is not displayed, press button

è

or

ÿ

on the multifunction steering

wheel (

컄

page 130) until the trip

odometer appears in the multifunction
display.

왘

Press and hold the reset button in the
instrument cluster (

컄

page 125) until

the trip odometer is reset.

Tachometer

The red marking on the tachometer
(

컄

page 24) denotes excessive engine

speed.

To help protect the engine, the fuel supply
is interrupted if the engine is operated
within the red marking.

Outside temperature indicator

!

Avoid driving at excessive engine
speeds, as it may result in serious
engine damage that is not covered by
the Mercedes-Benz Limited Warranty.

Warning!

G

The outside temperature indicator is not de-
signed to serve as an ice-warning device and
is therefore unsuitable for that purpose.

Indicated temperatures just above the freez-
ing point do not guarantee that the road sur-
face is free of ice. The road may still be icy,
especially in wooded areas or on bridges.

«
...
127
128
129
130
131
...
»

Summary of Contents for C 240



































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for C 240

Brand: Metra Electronics Pages: 14

Brand: Hama Pages: 2

Porsche 911 Turbo S Wheel

Brand: FANATEC Pages: 9

Brand: Harbor Freight Tools Pages: 4

10-8002-C11670C

Brand: Saleen Pages: 17

Brand: U.S. General Pages: 8

Brand: Subaru Pages: 19

Brand: NavLinkz Pages: 23

Brand: Axxess Pages: 8

Brand: Lexus Pages: 878

Brand: Road Ranger Pages: 3

SKT 170 HYUNDAI

Brand: Paser Pages: 4

Brand: Yakima Pages: 13

Brand: Comelit Pages: 20

Brand: Husky Pages: 18

ETSS100CBKFV-BP

Brand: Soundoff Signal Pages: 2

Brand: SAN HIMA Pages: 10

Brand: Maserati Pages: 288

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands