Mercedes-Benz C 240 Operator'S Manual Download Page 383

Page: 383 / 482

381

Practical hints

Where will I find ...?

In the case of a flat tire, you may
temporarily use the Minispare wheel when
observing the following restrictions:

앫

Do not exceed a vehicle speed of
50 mph (80 km/h).

앫

Drive to the nearest tire repair facility
to have the flat tire repaired or
replaced as appropriate.

앫

Do not operate vehicle with more than
one Minispare wheel mounted.

For more information, see “Rims and Tires”
(

컄

page 423).

Minispare wheel bolts

Wheel bolt for light alloy rims

Wheel bolt for Minispare wheel or other
steel rims (located in vehicle tool kit)

Wheel bolts

must be used when

mounting the Minispare wheel or other
steel rims. The use of any wheel bolts
other than wheel bolts

for the

Minispare wheel or other steel rims will
physically damage the vehicle’s
brakes.

Warning!

Make sure to use the original length wheel
bolts when remounting the original wheel
after it has been repaired.

Summary of Contents for C 240



































































































































































































































































































































































































































































































Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands

Mercedes-Benz C 240, Operator'S Manual

Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands