Mercedes-Benz C 240 Operator'S Manual Download Page 106

Page: 106 / 482

104

Controls in detail

Locking and unlocking

Locking

왘

Press central locking switch

If all doors are closed, the vehicle
locks.

Unlocking

왘

Press central unlocking switch

The vehicle unlocks.

You can open a locked door from the
inside. Open door only when conditions
are safe to do so.

If the vehicle was previously centrally
locked using the SmartKey, it will not
unlock using the central unlocking
switch

If the vehicle was previously locked
with the central locking switch

앫

while in the selective remote con-
trol mode, only the door opened
from the inside is unlocked.

앫

while in the global remote control
mode, the vehicle is unlocked
completely when a door is opened
from the inside.

Summary of Contents for C 240



































































































































































































































































































































































































































































































Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands

Mercedes-Benz C 240, Operator'S Manual

Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands