Mercedes-Benz C 240 Operator'S Manual Download Page 173

Page: 173 / 482

171

Controls in detail

Good visibility

왔

Good visibility

For information on the windshield wipers,
see “Windshield wipers” (

컄

page 50).

Headlamp cleaning system*

The switch is located on the left side of the
dashboard.

Headlamp washer switch

왘

Switch on ignition (

컄

page 33).

왘

Press switch

The headlamps are cleaned with a
high-pressure water jet.

For information on filling up the washer
reservoir, see “Windshield washer system
and headlamp cleaning system*”
(

컄

page 303).

Rear view mirrors

For more information on setting the rear
view mirrors, see “Mirrors” (

컄

page 41).

Interior rear view mirror, antiglare
position

Lever

왘

Tilt the mirror to the antiglare night
position by moving lever

towards

the windshield.

The interior rear view mirror is dimmed.

Summary of Contents for C 240



































































































































































































































































































































































































































































































Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands

Mercedes-Benz C 240, Operator'S Manual

Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands