Mercedes-Benz C 240 Operator'S Manual Download Page 197 | Manualshive

Page: 197 / 482

background image

195

Controls in detail

Automatic climate control*

Activating

왘

Press button

e

(

컄

page 187).

The indicator lamp on the button
comes on.

Deactivating

왘

Press button

e

(

컄

page 187).

The indicator lamp on the button goes
out.

i

If you keep button

e

pressed the

side windows and tilt/sliding sunroof*
will close.

i

The activated charcoal filter should be
switched off when windows fog up on
the inside, or if the passenger compart-
ment needs to be quickly heated or
cooled down.

Warning!

G

Never operate the side windows and the
tilt/sliding sunroof* if there is the possibility
of anyone being harmed by the closing pro-
cedure.

In the event that the closing procedure
causes potential danger, the closing of the
side windows can be immediately halted by
pressing or pulling the respective window
switch. The closing of the tilt/sliding
sunroof* can be immediately halted by
moving the tilt/sliding sunroof* switch in
the overhead control panel in any direction.

The closing of the side windows and
tilt/sliding sunroof* can be reversed by
again pressing and holding the button

e

.

i

If you keep button

e

pressed the

side windows an tilt/sliding sunroof*
will return to their previous position.

«
...
195
196
197
198
199
...
»

Summary of Contents for C 240



































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for C 240

Brand: Warrior Products Pages: 2

Brand: Saab Pages: 10

Brand: Haibang Pages: 6

Brand: femkes Pages: 7

Brand: BMW Pages: 38

Brand: Yakima Pages: 12

Brand: Axxess Pages: 16

Brand: true-i Pages: 11

Brand: Mobridge Pages: 20

84 61 0 028 926

Brand: BMW Pages: 13

Brand: Roadtrek Pages: 61

Brand: Hama Pages: 13

EQ forfour 2018

Brand: SMART Pages: 224

Brand: BMW Pages: 278

Brand: Pyle Pages: 14

Brand: Wallbox Pages: 21

Brand: TIS Pages: 6

PLATINUM HT051202

Brand: Haltech Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands