Mercedes-Benz C 240 Operator'S Manual Download Page 200

Page: 200 / 482

198

Controls in detail

Automatic climate control*

Rear passenger compartment
adjustable air vents

The air conditioning for the rear passenger
compartment is controlled via the auto-
matic climate control panel (

컄

page 187).

The air vents for the rear passenger
compartment are located in the rear
center console.

Left center air vent

Thumbwheel for air volume control for
center air vents

Right center air vent

Adjusting air distribution

왘

Push the slide for the left center
vent

or right center vent

to the

left, right, up, or down.

The air flow is directed in the
corresponding direction.

Adjusting air volume

왘

Turn thumbwheel

up or down.

The air volume is increased or
decreased.

The temperature at the center air vents
for the rear passenger
compartment

and

is the same as

at the dashboard center air vents.

For draft-free ventilation, push
slides

and

upward.

Summary of Contents for C 240



































































































































































































































































































































































































































































































Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands

Mercedes-Benz C 240, Operator'S Manual

Search results

Summary of Contents for C 240

Reviews:

Related manuals for C 240

Brands by name

Popular brands