Mercedes-Benz C 240 Operator'S Manual Download Page 177 | Manualshive

Page: 177 / 482

background image

175

Controls in detail

Good visibility

Rear window defroster

The rear window defroster uses a large
amount of power. To keep the battery
drain to a minimum, switch off the
defroster as soon as the rear window is
clear. The defroster is automatically
deactivated after approximately
6 to 17 minutes of operation depending on
the outside temperature.

Activating

왘

Press button

F

or

1

in the

climate control panel (

컄

page 177) or

automatic climate control panel*
(

컄

page 187).

The indicator lamp on the button
comes on.

Deactivating

왘

Press button

F

or

1

again.

The indicator lamp on the button goes
out.

Warning!

G

Any accumulation of snow and ice should be
removed from the rear window before
driving. Visibility could otherwise be
impaired, endangering you and others.

!

If the rear window defroster switches
off too soon and the indicator lamp
starts flashing, this means that too
many electrical consumers are
operating simultaneously and there is
insufficient voltage in the battery. The
system responds automatically by
deactivating the rear window defroster.

As soon as the battery has sufficient
voltage, the rear window defroster
automatically turns itself back on.

«
...
175
176
177
178
179
...
»

Summary of Contents for C 240



































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for C 240

Brand: Jeep Pages: 25

Brand: Paxton Automotive Pages: 85

Brand: Thule Pages: 8

Brand: Yakima Pages: 12

Brand: Yakima Pages: 13

Brand: Menabo Pages: 11

Brand: Phonocar Pages: 2

Brand: Maserati Pages: 210

Brand: OnStar Pages: 22

Brand: STC Pages: 6

Brand: Saab Pages: 12

Brand: Kia Pages: 51

Brand: Camecho Pages: 2

E60-82-007-02-10

Brand: Eibach Pages: 3

Brand: Ranger design Pages: 24

Brand: Caltrend Pages: 3

Brand: Thule Pages: 12

Brand: Fab Fours Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands